Rico Board上编译USB WiFi RT3070驱动
本帖最后由 ztshun 于 2015-8-11 09:47 编辑1.附件中提供了RT3070驱动源码包DPO_RT5572_LinuxSTA_2.6.1.3_20121022.tar.gz和编译好的驱动，这里选择使用taget_file.tar.gz中已经编译好的文件，其中还包括了与驱动相匹配的linux-3.12.10内核镜像。
2.将target_file目录下的RT2870STA.dat和rt3070sta.ko拷贝进Rico Board板子中
mkdir –p /etc/Wireless/RT2870STA/
cp RT2870STA.dat /etc/Wireless/RT2870STA/
cp rt3070sta.ko /home
3.加载驱动
root@RicoBoard home# insmod rt3070sta.ko
rtusb init rt2870 --->
=== pAd = e0936000, size = 512288 ===
<-- RTMPAllocAdapterBlock, Status=0
NVM is EFUSE
usbcore: registered new interface driver rt2870
4.然后可以通过ifconfig -a 可以看到系统已经正确识别网卡，名称为ra0
5 启动网卡ifconfig -a
root@RicoBoard home# ifconfig ra0 up
NICLoadFirmware: We need to load firmware
<-- RTMPAllocTxRxRingMemory, Status=0
RTMP_TimerListAdd: add timer obj e097e0b8!
RTMP_TimerListAdd: add timer obj e097e0e8!
RTMP_TimerListAdd: add timer obj e097e118!
RTMP_TimerListAdd: add timer obj e097e088!
RTMP_TimerListAdd: add timer obj e097dff8!
RTMP_TimerListAdd: add timer obj e097e028!
RTMP_TimerListAdd: add timer obj e094882c!
RTMP_TimerListAdd: add timer obj e0937d0c!
RTMP_TimerListAdd: add timer obj e0937d40!
RTMP_TimerListAdd: add timer obj e09488d0!
RTMP_TimerListAdd: add timer obj e09487cc!
RTMP_TimerListAdd: add timer obj e094889c!
-->RTUSBVenderReset
<--RTUSBVenderReset
Key1Str is Invalid key length(0) or Type(0)
Key2Str is Invalid key length(0) or Type(0)
Key3Str is Invalid key length(0) or Type(0)
Key4Str is Invalid key length(0) or Type(0)
1. Phy Mode = 5
2. Phy Mode = 5
NVM is Efuse and its size =2d
phy mode> Error! The chip does not support 5G band 5!
RTMPSetPhyMode: channel is out of range, use first channel=1
3. Phy Mode = 9
AntCfgInit: primary/secondary ant 0/1
MCS Set = ff 00 00 00 01
<==== rt28xx_init, Status=0
0x1300 = 00064300
注：如果出现ERROR: 256 KiB atomic DMA coherent pool is too small!的错误，请将 coherent_pool=2M，添加在uboot的启动参数qspiargs后面。
6 .配置wpa_supplicant配置文件（wpa_supplicant相关工具已经移植好，包含在我们提供的文件系统中）
vi /etc/wpa_supplicant.conf
编辑如下形式
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="XXXXXXXX"
scan_ssid=1
key_mgmt=WPA-EAP WPA-PSK IEEE8021X NONE
pairwise=TKIP CCMP
group=CCMP TKIP WEP104 WEP40
psk="XXXXXXXX"
}注：ssid无线网名字，psk为无线网密码，请根据自己具体路由设置进行编辑配置文件
7.连接 wpa_supplicant -Dwext -ira0 -c/etc/wpa_supplicant.conf&
root@RicoBoard home# wpa_supplicant -Dwext -ira0 -c/etc/wpa_supplicant.conf&
Successfully initialized wpa_supplicant
===>rt_ioctl_giwscan. 7(7) BSS returned, data->length = 1509
ra0: Trying to associate with 38:83:45:2c:c8:00 ==>rt_ioctl_siwfreq::SIOCSIWFREQ(Channel=1)
(SSID='TP-LINK-1201' freq=2412 MHz)
ra0: Associated with 38:83:45:2c:c8:00
ra0: WPA: Key negotiation completed with 38:83:45:2c:c8:00
ra0: CTRL-EVENT-CONNECTED - Connection to 38:83:45:2c:c8:00 completed
8.ping通外网
root@RicoBoard home# ifconfig ra0 192.168.1.24 netmask 255.255.255.0
root@RicoBoard home# route add default gw 192.168.1.1
root@RicoBoard home# ping www.baidu.com
PING www.baidu.com (119.75.217.109): 56 data bytes
64 bytes from 119.75.217.109: seq=0 ttl=53 time=72.089 ms
64 bytes from 119.75.217.109: seq=1 ttl=53 time=73.024 ms
64 bytes from 119.75.217.109: seq=2 ttl=53 time=72.862 ms
64 bytes from 119.75.217.109: seq=3 ttl=53 time=73.278 ms
64 bytes from 119.75.217.109: seq=4 ttl=53 time=73.044 ms
64 bytes from 119.75.217.109: seq=5 ttl=53 time=72.439 ms
64 bytes from 119.75.217.109: seq=6 ttl=53 time=72.777 ms
64 bytes from 119.75.217.109: seq=7 ttl=53 time=73.292 ms
9.附件
页:
[1]